Alocasia Corm Riser for the Puddle Method - Black

Regular Price
$8.90
Sale Price
$8.90
Regular Price
Unit Price
Translation missing: en.general.accessibility.unit_price_separator 
FREE Shipping for orders $99+
Pay Later Afterpay available
Fast Delivery 1 to 3 days most of NZ
Open 5 Years 40,000+ orders sent

Corm Risers reduce the risk of rot when growing alocasia corms using the puddle method. This is for one 3D printed Corm Riser made from PETG in black. Reusable over-and-over.


Which cups to get


These risers fit standard 2 ounce sauce cups (shown in the photos but not included), which are easy and cheap to get separately or use leftovers from takeaways. This is just for the Corm Riser by itself. 


These also fit in most small containers and multiples can be used in larger containers also. I just prefer the little 2 oz cups as it's a nice small size for fitting lots of corms in my cabinet and keeping humidity high individually.


I also prefer small separate containers with one corm in each to help prevent the spread of rot just in case to limit losses if anything goes wrong, although just adding the risers themselves helps with that also.

 

What is PETG?


These are made with higher quality PETG filament. PETG is stronger than the usual 3D printed filament with the added bonus of UV resistance for use under grow lights, bright natural light or sunlight. Its also has better chemical and heat resistance.


How I do the puddle method using a corm riser


Feel free to experiment. This is what's currently working for me. There are lots of handy tutorials on YouTube well worth a watch also about the puddle method... 


CORM PREP: I gently clean the corm first, removing any substrate and old roots, and although optional, I also prefer to carefully peel the dark outer protective layer off.


SET-UP:
After putting the corm riser inside a 2 oz sauce cup, I rest my corm on the riser with the pointed side of the corm facing up. I prefer one corm per riser per cup to reduce the risk of rot meaning I lose them all.


WATER:
I add water to the bottom so the level comes up to just below the bottom of the riser, barely touching or not touching the riser, but always making sure the corm is NOT submerged in the water at all. I use nutrient solution (I use 5mls of GT CCS per 1 litre of water).


LID: Then I pop the lid on the cup to lock in the humidity and reduce water loss. I also 'burp' my corm cups weekly (more about airflow below), and if I remember, I like to replace or top up with fresh nutrient solution weekly also.

 

Tips for alocasia corm growth success


I find light and nutrients less important for growing alocasia from corms as with other methods of propagating plants.


A good clean-up of the corm at the start sets you up for success. Any old roots or substrate left attached to the corm can increase the chance of rot. That's also why I like to 'peel' that brown outer layer off after I've cleaned everything else.


Once clean and set-up in its cup, I find the more important considerations are:

 

Consistent, constant moisture. No drying out! Yet you also don't want your corms sitting IN water (hence why the puddle method can be prone to rot without a corm riser to lift the corm up).

High humidity but still with airflow! Another reason rot is a risk is the need for high humidity but also airflow. I use the 'burp method' where I air out all my corm cups once to twice a week just for 5 to 10 minutes without the lids on I find is plenty (I have a fan in my cabinet).  


Warmth: I like to stick between 24 and 27 degrees Celsius. I use an Inkbird heat mat as I find it too hard to avoid dips below 24 overnight even in my Ikea cabinet (I have a converted Rusdta Wide).


Nutrients: The corm has its own starter store of nutrients to get things going (depending on how healthy it is), but that doesn't mean no nutrients are needed, just less. I tend to stay away from your typical high-nitrogen foliage fertilisers and use rooting fertilisers instead.


You could get away without any nutrients in the water until rooted, or just use a rooting fertiliser from the start (that's what I prefer as it's much easier to just make up the same nutrient solution for everyone in one go). My go-to is GT CCS propagation and rooting fertiliser. I use 5ml per 1 litre water.


Why add a corm riser to the puddle method?


Adding a corm riser is essentially an upgrade to the puddle method, so the general advice you'll find for the puddle method still applies.


A corm riser gives you better chance of success vs the water-only puddle method, since rot is the biggest worry with the puddle method.


I also prefer using a riser as you can keep a higher level of water in the cup, so it reduces the the worry of finding your corms have suddenly dried out and died, and makes it easier to keep that constant, high level of humidity.

 

Any plants, corms, plastic cups, lids, and any other accessories shown in photos NOT included. This is for the Corm Riser by itself.

 

 

Shipping and Delivery FAQ's


SHIPPING RATES


FREE SHIPPING for orders $99+. 

Or for orders under $99 > Auckland Urban $5.90 or rural $9.90. Rest of the North Island: Standard $8 or rural $12. South Island: Standard $9.90 or Rural $15.90 Outer islands (Waiheke, Stewart etc), have different rates (see full rates).

Overweight / oversize shipping may apply (see full rates & FAQs)


IN STOCK IN NZ


Stock levels are live. Everything showing in stock online, is in stock right here, right now, ready to ship. No drop shipping from other countries. No delays.

PRE-ORDERS > Pre-order products will be clearly marked pre-order and list the shipping date on the product page.

 

SHIPPING DAILY


Orders ship every week-day. Orders placed Monday to Thursday leave the next morning. Fri morning orders before 10am usually ship on Friday. Friday orders after 10am up to 10pm Sunday night leave Monday (or the next working day if Monday is a public holiday).

 

More shipping and delivery FAQs >

 

 

Why choose to buy from Love That Leaf?

100% NZ

Hi! I'm Anna, the owner of Love That Leaf. When you buy from me you're supporting a local, family business (and fellow houseplant hobbyist). Love That Leaf is a registered NZ business and is 100% NZ owned and operated. Orders ship daily, Monday to Friday, from Auckland. Usual delivery is 1 to 3 working days NZ wide.


I'LL PUT IT RIGHT

I stand by everything I sell. I'll always help if something goes wrong. When you choose to buy from a registered NZ business (like me), you're also covered by the Consumer Guarantees Act, unlike overseas purchases or private sales where you might end up stuck with no rights if anything arrives damaged or stops working.


SUPER SUPPORT

I'm here for support and advice anytime, even if you haven't bought from me yet. A lot of lovely people helped me along my plant journey, and I want to pay it forward. Please don't hesitate to ask for help. No obligation at all to purchase. 


5 YEARS

I started Love That Leaf in August 2020, currently have over 2,000 independent, verified 5 star reviews and have sent over 40,000 orders to houseplant hobbyists NZ-wide. Thank you for your support!